Wood Grain Glaze

CIFS® Wood Grain Finish

To finish strong and recreate the look of a wood finish over Continuous Insulation Systems (CI) you need a glaze formulated with 100% acrylic polymers for durability with good open time for the application process. Wood Grain Glaze used artistically over Wood Grain Tex specialty finish creating the look of wood with the durability of an acrylic finish and is formulated with DuroTone pigments for excellent color retention.

Systems
Rollershield Drainage CIFS®
Aggre-flex Drainage EIFS
Aggre-flex EIFS

Colors
Douglas Fir
Ivory
Oak
Metallic Cote – Antique Gray*
Walnut
Custom Colors Available

VOC: <1% by Weight VOC: 1.4 g/l Manufacture Locations: 30058 • 77474 • 84651 Recycled Content: 0% Packaging: 5 gallon (19L) pail

Pail Weight: 53 lbs (24 kg)

Coverage (estimated): 1000-1200 sf/pail (93-112 sm)

Working Time: About 1/2 hour.

Drying Time: Varies by air temperature, humidity and surface temperature.

Dry to Touch: 1/2 hour @ room temperature

Drying Time: 12 hours @ room temperature

Application/Storage Temperatures: 40°F (5°C) to 110°F (43°C). Store out of direct sunlight.

Shelf Life: 2 years under normal conditions.

Application Procedure

Job Conditions – Air and substrate temperature for application of Wood Grain Glaze must be 40°F (5°C) or higher and must remain 40°F (5°C) or higher for a minimum of 24 hours. Provide temporary protection until Wood Grain Glaze is fully dried. Store materials within prescribed temperature limits and out of direct sunlight. Working and drying times are based upon normal room temperature conditions and will vary with temperature and humidity.

Preparation – The Wood Grain Tex Finish must be clean, dry and ready to receive the acrylic coating.

Equipment Needed – Brush, 4”-6” (102-154 mm) Foam Roller, Spray bottle with water, Wood Grain Tool (Available from Master Wall®), Wood Grain Sealer.

Mixing – Thoroughly stir Wood Grain Glaze into a homogenous consistency. Small amounts of clean, potable water may be added to obtain a workable consistency. Do not over mix. Do not exceed 24 ounces (0.7L) of water per pail. Do not add accelerators or retarders to Wood Grain Glaze.

Application – Wood Grain Glaze is applied by brush or a moist foam roller.
Using a paint brush for latex paints, brush Wood Grain Glaze into the grooves of the finish.
Using a moist foam roller, roll a thin amount of Wood Grain Glaze onto the finish surface and keep a wet edge.

  • Using a spray bottle, wet the surface of the Wood Grain Glaze to thin and keep from tacking too quickly.
  • Add grain to the surface using the Wood Grain Tool along the length of the grooved finish, rocking the tool to create the desired pattern.
  • Once dry to the touch, lightly sand the surface if needed using 100-grit sandpaper to remove any high spots or heavy stain areas.
  • Using a sponge or roam roller, cover the entire surface with Wood Grain Sealer.

Clean Up
Tools and equipment can be cleaned with soapy water when Wood Grain Glaze is wet.

Limitations
Do not use Wood Grain Glaze as a finish directly over any Master Wall base coat.

Information contained in this product data sheet conforms to the standard detail recommendations and specifications for the installation of Master Wall Inc.® products and is presented in good faith. Master Wall Inc.® assumes no liability, expressed or implied as to the architecture, engineering, or workmanship of any project. This information may be concurrent with, or superseded by other applicable documents, such as specifications and details. Contact Master Wall Inc.® for the most current product information. ©2019 Master Wall Inc.®