Lightweight non adhesive roll flashing material with superior strength and the ability to bridge most gaps or voids common in construction. Embedded into wet Rollershield-RS, TG or VB, it is used at flashing transitions with Master Wall® SuperiorShield Liquid Air/Water Barrier (LAB) and as part of Rollershield Drainage CIFS® applications. The tape easily embeds into wet Rollershield and dries to a highly reinforced yet flexible flashing.

  • Lightweight
  • Strong
  •  Embeds easily
  • Thin, will not build up wall surface
  • Compatible with Rollershield RS, TG, VB and SuperiorFlash products

Coverage estimate*
4×8 sheets: Square Footage x 0.37 = linear feet of tape
Add linear footage around windows, doors, and other openings.
*All coverage is approximate and depend upon substrate, details and individual application


Roll Sizing/Packaging/Shelf Life/Storage
4”x180’ (10.2cm x 54.9m)
6”x180’ (15.2cm x 54.9m)
9”x180’ (22.9cm x 54.9m)
Packaging:
4”: 18 rolls per case.
6” & 9”: 12 rolls per case.
Shelf Life: 2 years plus Storage: Protect from extreme heat (90°F (32°C), and direct sunlight.


JOB CONDITIONS
Air and substrate temperature for application of SuperiorShield Flashing Tape must be 40°F (5°C) or higher. Follow Rollershield-RS, TG or VB temperatures and condition requirements.
PREPARATION
General—The substrate must be clean, dry, structurally sound, and free of efflorescence, oil, grease, form release agents and curing compounds. Test painted surfaces to verify bond.
Temporary Protection – Protect from weather until the Rollershield-RS, TG or VB products have set up.
Surface Preparation – Surface temperature must be above 40°F (5°C). Surface must be cured, clean, dry, structurally sound, and free of efflorescence, oil, grease, form release agents, and curing compounds.

APPLICATION PROCEDURE
General – SuperiorShield Flashing Tape is embedded into wet Rollershield-RS, TG or VB at flashing transitions (sheathing to framing, flashing, penetrations, etc.) and at sheathing board joints. Apply a generous layer of the product using a trowel, brush or roller and immediately embed the SuperiorShield Flashing Tape into the product and draw it tight and smooth working from the center to the edges.
Windows – The unique properties of the SuperiorShield air/water barrier system allows window flashing prior to the Rollershield wall application. Apply Rollershield and center SuperiorFlash Flashing Tape to provide at least at least 1” (25 mm) bond to the window flange and substrate on either side of the window opening. Use a “butterfly” at corners to complete the application making sure it covers all corner joints. For best results make sure the Rollershield covers the entire head, jamb, and sill areas. The use of sill wedges or water stops is encouraged.
Sheathing Applications — Apply Rollershield at least 2” (51 mm) either side of the sheathing board joint. Immediately embed the SuperiorShield Flashing Tape into the wet Rollershield and smooth with a trowel, centering it over the joint. Provide at least at least 1” (25 mm) bond either
side of the sheathing joint. Lap Rollershield Mesh Tape 2” (51 mm) minimum Rollershield field application can begin as soon as the Rollershield is dry to the touch.


Hazard: This chemical is not considered hazardous according to the OSHA Hazard Communication Standard 2012 (29 CFR 1910.1200).


VOC: Less than 50 g/L.


Approved Materials for Embedment
Rollershield-RS
Rollershield-TG
Rollershield-VB
Others approved in writing

Information contained in this product data sheet conforms to the standard detail recommendations and specifications for the installation of Master Wall® Inc. products and is presented in good faith. Master Wall® Inc. assumes no liability, expressed or implied as to the architecture, engineering, or workmanship of any project. This information may be concurrent with, or superseded by other applicable documents, such as specifications and details. Contact Master Wall® Inc. for the most current product information.